Monday, November 20, 2017

The Fly Sucker 2000

Bringing in the wood bins also brings in the flies that have hidden in the logs for the winter.  As they enjoy the (relative?) warmth of the cabin, they come out of hibernation, and inevitably head for the upstairs windows to escape.

In an effort to control the incessant buzzing and build-up of dessicated remains, I have invented the flysucker 2000.  It cost all of $7 from Home Depot.  A piece of ten foot electrical conduit jammed onto the end of the vacuum hose.  It doesn't have much power, you have to get right on top of the fly to trap it, but it is satisfying, and I suspect a little painters tape to seal the hose to the vacuum for better suction would only improve matters.

The mad genius at work.

Thursday, November 16, 2017

Boxing in the Stovepipe

When my stovepipe collar was first installed properly by Dan VanLenthe's crew, I was really surprised to find that the stovepipe itself was not in any way fastened, let alone sealed, to the collar itself!  That explained the purpose of the storm collar - it was to actually keep rain and such out of that gap betwixt the pipe and the rim of the collar.

My issue with that situation was that with a cathedral ceiling (essentially - the floor of the attic is not vapour sealed from the rest of the cabin), I essentially had a hole in my roof where the stovepipe stuck through!

Thinking myself somewhat clever, I packed the upper roof cone full of stone wool insulation and then sealed it all up with loads of foil tape.


The next time I was talking with the good fellows at Thunder Bay Fireplaces though, I was warned that this was not appropriate, and it was suggested to even be a fire hazard.  I'm not certain how though; I'd love to have someone enlighten me...

In any case, they suggested all sorts of schemes for dealing with this situation, but the one that made the most sense was to simply build a small "room" around the stovepipe in the attic and seal it off from the rest of the cabin.

I began this project last spring, but as the weather warmed up, it moved from a priority to a "maƱana" situation.

Of course, it hung over my head all summer, and with nothing particularly planned for a recent day, I steeled myself with a warm mug of tea, and slipped into my overalls.  I promised myself to just cut "one board" and then I could quit if it was too annoying or discouraging.  Of course, one board led to another and I pretty much would have finished the entire deal if I hadn't run out of expanding spray foam.

I put in sheets of closed cell foam on the floor and walls of the attic "room" around the stovepipe, and then sealed it with spray foam.  Then I piled more stone wool insulation on top of the floors until it was about four to six inches below the "no insulation above this line" mark on the stovepipe thimble.


Once more into the breech after six months of avoidance.
Hard to make out - this is a small crevice packed solid with a mass of dead flies.  Not the way I'd want to go!
Here's the final wall with most of the plywood installed.  I opted not to bother with a stud for extra support in the centre, as it's simply a barrier, and not at all structural.
The final wall in position.
I packed the outside top edge of the walls with stone wool to support the spray foam on the inside.  Note the transition to the latex foam at the top edge of the wall - it allowed me to install it with the can held upright in this tight space.
A view through the peephole.  Things look messy but functional.  I removed all the stone wool from the cavity above just before sealing in the stovepipe.
And on the floor, a deep covering of stone wool.  Just beneath the collar, you can see the red tape marking the maxium height of insulation.
Heading back downstairs.  The top piece of foam is just pressure-fit to allow me to reopen and inspect for the next month or two before I seal it up.  You can see the latex foam is looking even more sad that usual.  I will return soon with a fresh can to see if it works any better.
I was impressed that the fireproof spray foam still worked as if it was newly purchased.  The latex DAP foam seemed to have degraded significantly over the summer on the other hand, and at first simply ran out of the nozzle as a liquid.  I gave it a very vigorous shaking, and then it came out more like melted marshmallow.  I put it where I could, but as I was finishing up, several large areas "glooped" out of where they were suppose to be.  I will purchase more and see if I can't convince it to stay in place a bit better for me.


Ugh, the latex foam is clearly past its best before date.
Sadly, it was still 14 degrees Celsius inside the cabin when we woke up the next morning, after being 24 degrees around 3 p.m. when we put on the fire.  I'm not sure if dropping 10 degrees in 12 hours is considered good or bad in a conventional home - I don't know anyone who would let it get that cold.  I'd love to hear some comments about the struggles of other people in keeping their family warm in a cold environment.  I suspect that many of my readers are in the enviable position of only being a dial or button (or app?) away from quickly and efficiently warming their home.

Wednesday, November 15, 2017

A Weekend of Expanding Foam

Whelp, as is usual at this time of year here on the homestead, we're doing all sorts of things to try to keep the cabin as warm as possible.

One thing that I can't help but think makes a huge difference is sealing up clearly felt draughts.  At first I was considering continuing to use the DAP caulking that I have been buying by the case here at the homestead.  But after having Ranta Construction come out to relevel and check my door installations, and seeing B! use expanding foam (Window and Door edition - promised not to warp my frames), I decided that perhaps it would be a better choice.  This was also reinforced by my observation that the regular caulk I had applied a few years ago has already gotten hard and pulled away from the gaps it was intended to seal.

I have now used several different versions of expanding foam over the course of the past half decade here on the homestead, and have a few things to observe...

Even if you have to do lots of work with it around your place, it seems to me to be a better option to go with single use cans.  I purchased a gun, but found it unwieldy and hard to clean and ultimately gave it up.

Almost all the cans have to be installed while inverted.  This is okay 80% of the time when you are installing it in a situation where you still can have the...  pardon the pun...  can above your working area.  As soon as you are at a ceiling or close to one, you're out of luck though.

DAP brand expanding LATEX foam allows you to work with the can upright.  I get the vibe that the other foams are generally better, but an upright can counts for much in my book.  In my next blog post, I believe I'll outline an application where I use both types on the same job to complete the installation.

Back to the matter at hand - all the doors and windows that make up the regular orifices of the cabin.

I basically went around to all the spots that haven't had their trim work finished, and added a wide bead of expanding foam.  I was able to use a standard (upside down) can here as none of them were close to a ceiling.

Then I also used acrylic sheets I had purchased from Surecraft Plastics to create my usual inner "storm" windows.  I will also be purchasing five more panels to nearly complete my collection.

Upside down, working at the kitchen window 

And out the main cabin window.  Lots of goo here!

Ugh, moisture and mildew behind the chesterfield.  Time to hit it up with bleach and try to get some air circulating.

Another view in the kitchen.

Papa framed these windows already, so Kenny held the ladder while I vacuumed flies and then inserted the acrylic sheets.

In the bedroom, one can see the acrylic bowing out.  I stiffened it with aluminum channel.

Another view of Daddy and Kenny cooperating!

Saturday, November 11, 2017

A Calm Night

Another night as Kenny and I were about to head into our bedroom to read some more Harry Potter, I wanted to snap this picture showing the previously installed drapes.  I caught Donna working on her own blog, and while the quality of the picture leaves much to be desired, I think it did capture the quietness that accompanied the post-sauna end of the day.

Accidental Renaissance.

Friday, November 10, 2017

Industrial Chic Insulated Drapes For Our Log Cabin

Attention Pinterest people - here's one you can share!

As I outlined a day or two ago - I did up a prototype insulated drape in our bedroom.  I believe it looked and worked decently enough that I had permission to expand and improve the concept.

Early last Friday I was working at Howie's so I left the house shortly after six a.m. to try to be at Lowe's in lots of time to get some galvanized pipe cut to size and purchase the fittings.

Imagine my surprise when they had 10' lengths of 1/2" pipe and fittings, but they didn't have a means to cut and thread the pipes to my required sizes!

I decided to kill a few moments by purchasing the fittings I needed, but I passed on the pipes so I could purchase them from Home Depot, where I knew they did have a cutter/threader.

I drove over to Home Depot and thankfully was only about five minutes before they opened.  It was a cold morning so I went inside anyway, but B! down at the contractor entrance blocked my way with friendly banter while I waited for the official store opening.  I later learned that she had made hot chocolate for the staff, but sadly, she didn't offer me any.

I got to plumbing, but hark!  They didn't have galvanized 1/2" pipe!  I offered DM! who was working their whatever he wanted in exchange for letting me bring in outside pipe to get cut and threaded.  I told him I would be back in fifteen minutes.

Embarrassed, I returned to Lowe's and purchased their last four lengths of pipe, went through the same checkout as earlier, and then headed back AGAIN to Home Depot.  Thank goodness I left myself lots of time!

Chatting extensively with DM! - who, by the way, is a real credit to the Home Depot organization - he cut my pipes exact to size and then walked me out of the store to the truck.

I raced to WalMart and purchased three sets of quilted sheets.  One Queen (for the main patio door) and two Twin (for the large cabin windows).

The next day I got out my random orbital Ryobi One+ sander and froze my hands off buffing the pipes clean of grease marks and oil.

I should have zipped up the sides of my pants!  No wonder I had a chill!
I brought them inside to dry out, and wiped them down with our industrial paper towels.

Almost as long as the whole cabin!
When I was sure that there wasn't any excessive moisure inside the pipes, I assembled them together and with Donna and Kenny's assistance, mounted them above the windows and doors.

I was careful to thread the rings on the pipes before screwing them to the walls - amazing foresight for me!

Rings go on before the ends or else...

Lining up to the panelling.  Interesting how the screws would pull in the panelling too - I guess they sagged a bit?

Looks good!
Then we unpacked the quilted sheets and clipped them up.  They transmitted even more light than I expected, but they looked really good and make me feel like we're saving a few precious energetic molecules of heat each night!

Co-operating with my love.

Now just letting her do all the work.
Now for the big... conceal!



Closeup of the quilting on the comforter.  The other quilts are much tighter stitching so hopefully no sag.

Kenny is perfect for pulling these drapes back and forth!

He's a born drape model!

Thursday, November 9, 2017

How to Easily Dry the Inside of a Bottle

As many of you know, I dabble in making very simple homemade cider.

Yes, homemade cider.

Did I say homemade cider?

In any case, one challenge was trying to dry the inside of the bottles in any sort of good time.  I tried turning them upside down, I tried turning them right side up and putting them in the warming closet or on the warm woodstove.

Finally I rolled up some paper towel and tucked it into the bottle for a few hours.  The dry towel quickly absorbs the moisture and then can be removed and composted.


Just thought you may like a quiiiiicccccccckkkkkkkkkkk tip!  (To quote Bigger Pockets).

Wednesday, November 8, 2017

A Prototype Insulated Drape

Since we've moved into the cabin, I've thought about some sort of way of insulating the windows either when we're not around, or when it's nighttime and we don't really see much out of them anyway.

Insulated drapes seemed the way to go, but the commercial solutions were frightfully expensive and seemed rather flimsy to me.

The other day I purchased an "inexpensive" quilt in a neutral grey, as well as some curtain rings with clips on them to allow one to clip their own fabric up.

I put in a few hooks above our bedroom door and we tried it out.

Very simple to test the theory.

Even at night though, I could see through this a bit under the light of the full moon.
While the room still was chilly, I mentally insist that it MUST have helped a bit, especially as the window in behind frosted up much more than usual, and so now I'm going to expand and improve the programme to some of the other windows on the main floor.



Thursday, November 2, 2017

Winterizing the Patio Doors

Last year I fought a bit with large acrylic sheets on the patio doors with limited success.  This year I have decided to return to the Dollarama plastic films to put over the doors.

To facilitate installation, I decided to try to remove the inside handle on the right hand side where it sticks in from the frame significantly.

Unfortunately that left holes open right through the door!  So then I moved to putting the flat handle on the inside (instead of the outside for screen clearance).

Basically I had to take both handles completely apart and mix and match them to get them back together.  It also meant that I could no longer lock the right hand side door.  This wasn't a big deal to me, as I had already cut some short boards to wedge in the bottom track to hold the doors extra tightly shut.

I also had to remove the spacer on the left side handle that helped it line up better with the latching mechanism.  This actually made the left side door tighten down even more, so that's a good thing.  I moved the spacer to the right side door where it was required.

Everything seems to have worked out well.  Of course, there is always the law of unintended consequences to rear its head eventually.

When it came time to install the film, instead of installing the two sided tape directly to the door frame, this year I am trying to first install painters tape all around, and then the two sided tape, to see if it makes for easier cleanup.  There are some windows where there are layers of two sided tape on the frames because I have been unable to remove it in the spring.

We'll keep our fingers crossed again that the painters tape can stand up to a full heating season.

Left inside before.

Right inside before.

Left outside before.

Right outside before.

Removed the extensions before realizing they couldn't go anywhere else.

You can see the spacer thingy at the bottom of the handle.

Left inside after - only difference is that it no longer has that spacer.  I was still able to tighten it right down nicely.

Left inside is not much more flush to the glass.  But the latch is a problem.

Removed the little latchy part, then turned the plate around so it...

Somewhat filled the slot that it had come out of.

Wednesday, November 1, 2017

Installing an Interior Storm Window on the Bathroom

Last season on the bathroom window I tried installing a sheet of acrylic to make it a bit more efficient.  It worked quite well I believe, but when it was time to remove it, I had a devil of a time pulling it away from the "draught attack" caulking I had applied.

This year I thought I'd see how well Dollarama painters tape could stand up for the duration of the heating season.

I believe it doesn't look too bad, but we'll see how well it stays up as the season goes on.